ВНИМАНИЕ!!!!


Автор Тема: Return to Stock  (Прочитано 1894 раз)

0 Пользователей и 1 Гость просматривают эту тему.

Оффлайн grahambell

  • Newbie
  • Сообщений: 18
  • Вес голоса: 1
  • grahambell не имеет никакого влияния.
  • Город: DR500 HD
Return to Stock
« : 31 Января 2014, 04:21:32 »


I followed these steps to return to stock FW 1.011

""hi. you just install DR500GW-HD_v1.008E(2013_0730)_Setup.exe on harddisk.
then folder BlackVue\System\upgrade from 1.008E firmware (from harddisk, eg C:\BlackVue\System\Upgrade) just replace folder BlackVue\System\upgrade on microSDCard.""

The dvd is working ok, but I can still see files from custom FW still on the DVR, example /mnt/mmc/blackvue/config/avserver.sh, rtlhostapd.conf etc. i also had a version mismatch error announced on startup. Below is an example of the log file:

[12:01:42][JC:check_model_info:1395]app_version:[1.011]

[12:01:42][JC:check_model_info:1399]app_model:[500GW]

[12:01:42][JC:check_model_info:1403]app_language:[English]

[12:01:42][JC:check_model_info:1410]cli_version:[2.101]

[12:01:42][JC:check_model_info:1414]cli_model:[500GW]

[12:01:42][JC:check_model_info:1418]cli_language:[English]

[12:01:42][JC:check_model_info:1425]cfg_version:[1.040]

[12:01:42][JC:check_model_info:1429]cfg_model:[500GW]

[12:01:42][JC:check_model_info:1433]/mnt/mmc/BlackVue/Config/version.bin read End

[12:01:42]#####[check_version:1484]firmware_version:1.011, FIRMWARE_VERSION:1.011

[12:01:42][check_version:1501] config.ini is 1.040...

[12:01:51][JC:pta_parameter_init:3404] overwrite set >>>> (time)

[12:01:54]Start_System

So my question is:

1.  Have i followed the correct procedure to return to stock FW or are there additional steps to completely remove all traces of the custom FW from the DVR, this info would be useful if i need to return the DVR to the supplier.

2. What hardware do i need to make the UART cable to make mod's via serial connection? and where could i buy these ?

Реклама на сайте."Баннер 728x90"

Оффлайн welder

  • Programmer
  • Hero Member
  • *****
  • Сообщений: 524
  • Country: mon
  • Вес голоса: 14
  • welder has a powerful will.welder has a powerful will.welder has a powerful will.welder has a powerful will.welder has a powerful will.welder has a powerful will.welder has a powerful will.
Re: Return to Stock
« Ответ #1 : 31 Января 2014, 12:10:22 »
Did you clear sd card after upgrade?

Оффлайн grahambell

  • Newbie
  • Сообщений: 18
  • Вес голоса: 1
  • grahambell не имеет никакого влияния.
  • Город: DR500 HD
Re: Return to Stock
« Ответ #2 : 01 Февраля 2014, 18:24:42 »
Hi

No copied just copied the upgrade folder to the existing SD card that contained the Custom FW, i didn't find any instructions to clear the card?

Regs
Graham

 

Яндекс.Метрика
Flag Counter