U-Boot 2010.06 (Jun 26 2013 - 15:42:37)
DRAM: 512 MiB
NAND: Special Nand id table Version 1.23
Nand ID: 0xEC 0xF1 0x00 0x95 0x40 0xEC 0xF1 0x00
Nand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:1bit
128 MiB
Can't find a valid spi flash chip.
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
user init finish.
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x500000
5242880 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.35.7
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2424848 Bytes = 2.3 MiB
Load Address: 80800000
Entry Point: 80800000
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.7 (root@sejung-ubuntu) (gcc version 4.4.1 (Hisilicon_v100(g
cc4.4-290+uclibc_0.9.30.2+eabi+linuxpthread)) ) #12 Fri Jun 14 17:33:44 KST 2013
CPU: ARMv7 Processor [412fc098] revision 8 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: godeyes
HIETH[hieth_mdio_intf_parse_tag] mdio_intf use:rgmii!
Memory policy: ECC disabled, Data cache writeback
l2cache_flush_all:l2cache_flag = 0,L2 cache may not enable!
l2cache_flush_range:l2cache_flag = 0,L2 cache may not enable!
l2cache_flush_range:l2cache_flag = 0,L2 cache may not enable!
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 34290
Kernel command line: mem=135M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfst
ype=yaffs2 mtdparts=hinand:1M(boot),15M(kernel),40M(rootfs),64M(patch),-(test)
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 135MB = 135MB total
Memory: 132072k/132072k available, 6168k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xe0000000 ( 376 MB)
lowmem : 0xc0000000 - 0xc8700000 ( 135 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc001f000 ( 92 kB)
.text : 0xc001f000 - 0xc040e000 (4028 kB)
.data : 0xc0428000 - 0xc0463440 ( 238 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:96
Console: colour dummy device 80x30
Calibrating delay loop... 878.18 BogoMIPS (lpj=4390912)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
NET: Registered protocol family 16
L2cache cache controller enabled
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 46) is a AMBA/PL011
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 47) is a AMBA/PL011
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
fuse init (API version 7.14)
msgmni has been set to 257
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
brd: module loaded
loop: module loaded
nbd: registered device at major 43
Spi id table Version 1.22
Hisilicon Spi Flash Controller V300 Device Driver, Version 1.10
Special nand id table Version 1.33
Hisilicon Nand Flash Controller V301 Device Driver, Version 1.10
Nand ID: 0xEC 0xF1 0x00 0x95 0x40 0xEC 0xF1 0x00
Nand(Hardware): Block:128KB Page:2KB Chip:128MB OOB:64B ECC:1bit
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bi
t)
5 cmdlinepart partitions found on MTD device hinand
Creating 5 MTD partitions on "hinand":
0x000000000000-0x000000100000 : "boot"
0x000000100000-0x000001000000 : "kernel"
0x000001000000-0x000003800000 : "rootfs"
0x000003800000-0x000007800000 : "patch"
0x000007800000-0x000008000000 : "test"
Fixed MDIO Bus: probed
hi_gmac_mii: probed
rtw driver version=v3.3.2_3192.20120103
usbcore: registered new interface driver rtl8192cu
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 68, io mem 0x100b0000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 69, io mem 0x100a0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2
registered taskstats version 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
yaffs: dev is 32505858 name is "mtdblock2" rw
yaffs: passed flags ""
mmc0: new high speed SDHC card at address 0001
usb 1-1: new high speed USB device using hiusb-ehci and address 2
mmcblk0: mmc0:0001 00000 29.2 GiB
mmcblk0: p1
VFS: Mounted root (yaffs2 filesystem) on device 31:2.
devtmpfs: mounted
Freeing init memory: 92K
register rtw_netdev_ops to netdev_ops
CHIP TYPE: RTL8188C_8192C
usb_endpoint_descriptor(0):
bLength=7
bDescriptorType=5
bEndpointAddress=81
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_in = 1
usb_endpoint_descriptor(1):
bLength=7
bDescriptorType=5
bEndpointAddress=2
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_out = 2
usb_endpoint_descriptor(2):
bLength=7
bDescriptorType=5
bEndpointAddress=3
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_out = 3
usb_endpoint_descriptor(3):
bLength=7
bDescriptorType=5
bEndpointAddress=84
wMaxPacketSize=40
bInterval=1
RT_usb_endpoint_is_int_in = 4, Interval = 1
nr_endpoint=4, in_num=2, out_num=2
USB_SPEED_HIGH
_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __ / - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________
[RCS]: /etc/init.d/S00devs
mknod: /dev/ttyAMA0: File exists
mknod: /dev/ttyAMA1: File exists
[RCS]: /etc/initChip Version ID: VERSION_NORMAL_TSMC_CHIP_88C.
.d/S01udev
RF_Type is 3!!
EEPROM type is E-FUSE
====> ReadAdapterInfo8192C
Boot from EFUSE, Autoload OK !
EEPROMVID = 0x0bda
EEPROMPID = 0x8176
EEPROMCustomerID : 0x00
EEPROMSubCustomerID: 0x00
RT_CustomerID: 0x00
_ReadMACAddress MAC Address from EFUSE = 00:25:42:e0:b4:90
EEPROMRegulatory = 0x0
_ReadBoardType(0)
BT Coexistance = disable
RT_ChannelPlan: 0x0a
_ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
### PS params=> power_mgnt(0),usbss_enable(0) ###
### AntDivCfg(0)
readAdapterInfo_8192CU(): REPLACEMENT = 1
<==== ReadAdapterInfo8192C in 190 ms
rtw_macaddr_cfg MAC Address = 00:25:42:e0:b4:90
MAC Address from pnetdev->dev_addr= 00:25:42:e0:b4:90
bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
[RCS]: /etc/init.d/S02pitta
###############################################
###############################################
### application start... ######
###############################################
###############################################
Hisilicon Media Memory Zone Manager
hi3516_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Hisilicon UMAP device driver interface: v3.00
pa:88700000, va:c8900000
load sys.ko for Hi3516...OK!
load h264e.ko ....OK!
load mpeg4e.ko success.
ISP Mod init!
load vou.ko ....OK!
load vpp.ko ....OK!
load vda.ko ....OK!
load rc.ko ....OK!
load region.ko ....OK!
load ive.ko ....OK!
load tde.ko ....OK!
hifb info: HIFB_MAIN_VERSION[HIFB_MAIN_VERSION] Build Time[Dec 3 2012, 10:42:35
]
hifb info: video:vram0_size:1843200,vram1_size:1843200,vram2_size:1843200,vram8_
size:1658880
hifb info: succeed in registering the fb0: ovl0 frame buffer device
hifb info: succeed in registering the fb1: ovl1 frame buffer device
hifb info: succeed in registering the fb2: ovl2 frame buffer device
hifb info: succeed in registering the fb3: ovl8 frame buffer device
Sensor_A type is imx122
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2003009c: 0x00000002 --> 0x00000006
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/Kernel: ssp initial ok!
cmdshell.c:166}cmdstr:himm
0x200f0148: 0x00000000 --> 0x00000001
acodec inited!
/dev/mmcblk0p1 mount....
yaffs: dev is 32505859 name is "mtdblock3" rw
yaffs: passed flags ""
wlan found..0/5 sec..==> [ wlan0 Link encap:+871x_drv - drv_open, bup=0
Ethernet HWaddr 00:25:42:E0:B4:90 ]
===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC
FirmwareDownload92C accquire FW from embedded image
fw_ver=v79, fw_subver=0, sig=0x88c0
fw download ok!
Set RF Chip ID to RF_6052 and RF type to 1T1R.
IQK:Start!!!
Path A IQK Success!!
Path A IQK Success!!
IQK: final_candidate is 0
IQK: RegE94=102 RegE9C=e RegEA4=fe RegEAC=2 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
Path A IQ Calibration Success !
pdmpriv->TxPowerTrackControl = 1
MAC Address from REG_MACID = 00:25:42:e0:b4:90
rtl8192cu_hal_init in 650ms
MAC Address = 00:25:42:e0:b4:90
-871x_drv - drv_open, bup=1
wlan up!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
survey done event(1a)
wlan scanning..!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
best channel copying...!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
nand app not exists...Factory Upgrade Starting...
Running new_upgrade!!
- /mnt/mmc/BlackVue/System/new_upgrade [1]system_start
[board ver check]>>>>>>>>>> revision num : 0x00
*** Beging RAInitResamplerRat ***
[JC:led_set:678] LED_ALL_OFF
#### I am called by system_start!!! :-) JCH.
>>>>>>>>>>>>>>>>>>[new_upgrade:main:1089] START<<<<<<<<<<<<<<<<<<<<
NAND filesystem : yaffs2
Kernel have yaffs2 filesystem
sue OK /mnt/mmc/BlackVue/System/upgrade/patch_DR550GW.bin:/mnt/mmc/BlackVue/Syst
em/upgrade/patch_DR550GW.sue
??A??AAI ??±?·?AIµa °?Ao..ok [/mnt/mmc/BlackVue/System/upgrade/patch_DR550GW.bin
]
sue OK /mnt/mmc/BlackVue/System/upgrade/yaffs2fsImage_DR550GW:/mnt/mmc/BlackVue/
System/upgrade/yaffs2fsImage_DR550GW.sue
·c?®?AAI?A??AU ??±?·?AIµa °?Ao..ok [/mnt/mmc/BlackVue/System/upgrade/yaffs2fsIma
ge_DR550GW]
[main:1178]img_ok:4, patch_ok:1
[get_version_info:861]
app_version:[1.014][get_version_info:865]app_model:[550GW]
[get_version_info:869]
app_language:[Korea][get_version_info:876]cli_version:[2.101]
[get_version_info:880]cli_model:[550GW]
[get_version_info:884]cli_language:[Korea]
[get_version_info:891]cfg_version:[1.040]
[get_version_info:895]cfg_model:[550GW]
[get_version_info:899]/mnt/mmc/BlackVue/Config/version.bin read End
###[main:1327]firmware_language:Korea
pthread_create : motion_main DONE
[JC:led_set:678] LED_ALL_OFF
[04:00:16][main:1401]
/mnt/nand/voices/ : Voice DB None!!Segmentation fault
[RCS]: /etc/init.d/S80network
(none) login: root
Password:
Jan 1 00:00:31 login[906]: root login on 'console'
-sh: can't access tty; job control turned off
Welcome to HiLinux.
None of nfsroot found in cmdline.
#