DM36x initialization passed!
TI UBL Base Version: 1.50
Boot Loader BootMode = NAND
Starting NAND Copy...
Valid magicnum, 0xA1ACED66, found in block 0x00000008.
Boot Mode Task Completed
IPNC UBL Version: 1.1.0
Platform: DM368
Jumping to entry point at 0x81080000
U-Boot 1.3.4 (Dec 13 2012 - 15:36:20) DM368-IPNC-1.1.1
I2C: ready
DRAM: 256 MB
NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3, 3V 8-bit)
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
128 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
ARM Clock :- 432MHz
DDR Clock :- 340MHz
Ethernet PHY: GENERIC @ 0x00
Press "d" or " " to abort autoboot in 1 seconds
NAND read: device 0 offset 0x500000, size 0x500000
5242880 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.18_pro500-davinci_IPNC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2044048 Bytes = 1.9 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Linux version 2.6.18_pro500-davinci_IPNC_DM368_2.6.0 (root@ubuntu26-TI) (gcc version 4.2.0 (MontaVista 4.2.0-16.0.32.0801914 2008-08-30)) #1 PREEMPT Wed May 8 22:14:04 KST 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: DaVinci DM368 IPNC
Memory policy: ECC disabled, Data cache writeback
DaVinci DM0365 variant 0x8
PLL0: fixedrate: 24000000, commonrate: 170000000, vpssrate: 340000000
PLL0: vencrate_sd: 75555555, ddrrate: 340000000 mmcsdrate: 48571428
PLL1: armrate: 432000000, voicerate: 20571428, vencrate_hd: 27000000
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Built 1 zonelists. Total pages: 32768
Kernel command line: mem=128M console=ttyS1,115200 root=/dev/mtdblock3 rootfstype=cramfs,squashfs ip=off mtdparts=nand_davinci.0:0x300000(boot),0x200000(env),0x500000(kernel),0x3000000(rootfs),0x4000000(data1),-(data2) eth=96:a6:6c:45:e2:c0 board=DR500T
TI DaVinci EMAC: kernel boot params Ethernet address: 96:a6:6c:45:e2:c0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Clock event device timer0_0 configured with caps set: 07
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125440KB available (3341K code, 907K data, 184K init)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
DaVinci: 104 gpio irqs
MUX: initialized GPIO20
MUX: initialized I2C_SCL
MUX: initialized CLKOUT1
Generic PHY: Registered new driver
ch0 default output "COMPOSITE", mode "NTSC"
VPBE Encoder Initialized
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 4096 bind 2048)
TCP reno registered
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.1 (2006/08/19) Phillip Lougher
JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
yaffs May 8 2013 22:11:55 Installing.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
sbulla:<5>Req dev 0 dir 0 sec 0, nr 8 f 944
unknown partition table
LTT : ltt-facilities init
LTT : ltt-facility-core init in kernel
LTT : ltt-facility-statedump init in kernel
LTT : ltt-relay init
ltt-control init
LTT : ltt-facility-statedump init
DAVINCI-WDT: DaVinci Watchdog Timer: heartbeat 60 sec
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO map 0x1c20000 mem 0xfbc20000 (irq = 40) is a 16550A
serial8250.0: ttyS1 at MMIO map 0x1d06000 mem 0xfbd06000 (irq = 41) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
rtw driver version=v3.4.3_4369.20120622
Build at: May 8 2013 22:12:41
usbcore: registered new driver rtl8192cu
Davinci EMAC MII Bus: probed
MAC address is 96:a6:6c:45:e2:c0
TI DaVinci EMAC Linux version updated 4.0
netconsole: not configured, aborting
Linux video capture interface: v2.00
Trying to register davinci display video device.
layer=c06a7c00,layer->video_dev=c06a7d60
Trying to register davinci display video device.
layer=c06a7a00,layer->video_dev=c06a7b60
davinci_init:DaVinci V4L2 Display Driver V1.0 loaded
i2c /dev entries driver
nand_davinci nand_davinci.0: Using 4-bit hardware ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
6 cmdlinepart partitions found on MTD device nand_davinci.0
Creating 6 MTD partitions on "nand_davinci.0":
0x00000000-0x00300000 : "boot"
0x00300000-0x00500000 : "env"
0x00500000-0x00a00000 : "kernel"
0x00a00000-0x03a00000 : "rootfs"
0x03a00000-0x07a00000 : "data1"
0x07a00000-0x08000000 : "data2"
nand_davinci nand_davinci.0: hardware revision: 2.3
musb_hdrc: version 6.0/dbg, pio, host, debug=1
musb_hdrc: USB Host mode controller at c88e6000 using PIO, IRQ 12
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
[drivers/rtc/rtc-pcf8563.c:pcf8563_probe:288]kind(-1) return
pcf8563 0-0051: chip found, driver version 0.4.2
pcf8563 0-0051: rtc intf: proc
pcf8563 0-0051: rtc intf: dev (254:0)
pcf8563 0-0051: rtc core: registered pcf8563 as rtc0
davinci-mmc davinci-mmc.0: Supporting 4-bit mode
davinci-mmc davinci-mmc.0: Using DMA mode
Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
>>>[mmc_setup:1426] power_mode:MMC_POWER_OFF[0]
ASoC version 0.13.1
MUX: initialized MCBSP_BDX
MUX: initialized MCBSP_X
MUX: initialized MCBSP_BFSX
MUX: initialized MCBSP_BDR
MUX: initialized MCBSP_R
MUX: initialized MCBSP_BFSR
wm8960: WM8960 Audio Codec 0.2
asoc: WM8960 <-> davinci-i2s mapping ok
mmcblk0: mmc0:0007 SD64G 61882368KiB
mmcblk0: p1
ALSA device list:
#0: DaVinci DM365 WM8960 (WM8960)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
Time: timer0_1 clocksource has been installed.
Clock event device timer0_0 configured with caps set: 08
Switched to high resolution mode on CPU 0
pcf8563 0-0051: low voltage detected, date/time is not reliable.
pcf8563 0-0051: setting the system clock to 2010-01-11 01:54:46 (1263174886)
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 184K
INIT: version 2.86 booting
0
mkdir: can't create directory '/dev/.test': Read-only file system
Done /etc/rc.d/rcS.d/S03mountvirtfs..
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Done /etc/rc.d/rcS.d/S04udev..
Starting Dropbear SSH server: dropbear.
Done /etc/rc.d/rcS.d/S36dropbear..
Done /etc/rc.d/rcS.d/S41portmap..
###############################################
###############################################
### application start... ######
###############################################
###############################################
/dev/mmcblk0p1 mount....
Mount patch area at nand flash...
yaffs: dev is 32505860 name is "mtdblock4"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.4, "mtdblock4"
yaffs tragedy: Bad object type, -78143499 != 11, for object 129994303 at chunk 4990 during scan
yaffs tragedy: Bad object type, -201344003 != 7, for object 228585082 at chunk 4989 during scan
yaffs tragedy: Bad object type, 2147450878 != 1, for object 237862910 at chunk 4988 during scan
mount: wrong fs type, bad option, bad superblock on /dev/mtdblock4,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
CSL: Module install successful, device major num = 253
CSL: Module version 0.10.00, built on Mar 13 2014 17:15:34
I2C: Module install successful, device major num = 252
DMA: Module install successful, device major num = 251
DRV: Module install successful
DRV: Module built on Mar 13 2014 17:15:36
DRV: EDMACC.QUEPRI = 00000777
DRV: SYSTEM.MSTPRI0 = 00440022
DRV: SYSTEM.MSTPRI1 = 00000244
DRV: ISP.BCR = 00000002
DRV: SYSTEM.MISC = 00000319
CMEMK module: built on Mar 27 2013 at 18:15:50
Reference Linux version 2.6.18
File /home/sejung/project/DR500/dvsdk_2_10_01_18/linuxutils_2_24_03/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c
allocated heap buffer 0xc9000000 of size 0x8000000
CMEM Range Overlaps Kernel Physical - allowing overlap
CMEM phys_start (0x1000) overlaps kernel (0x80000000 -> 0x88000000)
cmemk initialized
EDMAK module: built on Mar 27 2013 at 18:15:52
Reference Linux version 2.6.18
File /home/sejung/project/DR500/dvsdk_2_10_01_18/linuxutils_2_24_03/packages/ti/sdo/linuxutils/edma/src/module/edmak.c
IRQK module: built on Mar 27 2013 at 18:15:53
Reference Linux version 2.6.18
File /home/sejung/project/DR500/dvsdk_2_10_01_18/linuxutils_2_24_03/packages/ti/sdo/linuxutils/irq/src/module/irqk.c
irqk initialized
[JC:82] CSL_gpioSet[flag:1]
wlan0 waitting... 1/5 sec.
usb 1-1: new high speed USB device using musb_hdrc and address 2
usb 1-1: configuration #1 chosen from 1 choice
CHIP TYPE: RTL8188C_8192C
usb_endpoint_descriptor(0):
bLength=7
bDescriptorType=5
bEndpointAddress=81
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_in = 1
usb_endpoint_descriptor(1):
bLength=7
bDescriptorType=5
bEndpointAddress=2
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_out = 2
usb_endpoint_descriptor(2):
bLength=7
bDescriptorType=5
bEndpointAddress=3
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_out = 3
usb_endpoint_descriptor(3):
bLength=7
bDescriptorType=5
bEndpointAddress=84
wMaxPacketSize=40
bInterval=1
RT_usb_endpoint_is_int_in = 4, Interval = 1
nr_endpoint=4, in_num=2, out_num=2
USB_SPEED_HIGH
Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C.
RF_Type is 3!!
EEPROM type is E-FUSE
====> ReadAdapterInfo8192C
Boot from EFUSE, Autoload OK !
EEPROMVID = 0x0bda
EEPROMPID = 0x8176
EEPROMCustomerID : 0x00
EEPROMSubCustomerID: 0x00
RT_CustomerID: 0x00
_ReadMACAddress MAC Address from EFUSE = 00:25:42:e0:86:a1
EEPROMRegulatory = 0x0
_ReadBoardType(0)
BT Coexistance = disable
RT_ChannelPlan: 0x0a
_ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
### PS params=> power_mgnt(0),usbss_enable(0) ###
### AntDivCfg(0)
readAdapterInfo_8192CU(): REPLACEMENT = 1
<==== ReadAdapterInfo8192C in 110 ms
rtw_macaddr_cfg MAC Address = 00:25:42:e0:86:a1
MAC Address from pnetdev->dev_addr= 00:25:42:e0:86:a1
bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
+871x_drv - drv_open, bup=0
wlan found..1/5 sec..==> [ wlan0 Link encap: ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC
Ethernet HWaddrFirmwareDownload92C accquire FW from embedded image
00:25:42:E0:86:fw_ver=v80, fw_subver=0, sig=0x88c0
A1 ]
fw download ok!
Set RF Chip ID to RF_6052 and RF type to 1T1R.
IQK:Start!!!
Path A IQK Success!!
Path A IQK Success!!
IQK: final_candidate is 0
IQK: RegE94=100 RegE9C=b RegEA4=fe RegEAC=2 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
Path A IQ Calibration Success !
pdmpriv->TxPowerTrackControl = 1
MAC Address from REG_MACID = 00:25:42:e0:86:a1
rtl8192cu_hal_init in 540ms
MAC Address = 00:25:42:e0:86:a1
-871x_drv - drv_open, bup=1
wlan up!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
survey done event(16)
wlan scanning..!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
best channel copying...!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
nand app not exists...
Factory Upgrade Starting...
Running new_upgrade!!
killall: telnetd: no process killed
killall: inetd: no process killed
- /mnt/mmc/BlackVue/System/new_upgrade [1]system_start
[JC:led_set:639] LED_ALL_OFF
#### I am called by system_start!!! :-) JCH.
Simple mixer control 'Left PCM',0
Capabilities: pswitch
Playback channels: Front Left - Front Right
Mono:
Front Left: Playback
[on]
Front Right: Playback [on]
>>>>>>>>>>>>>>>>>>[new_upgrade:main:1357] START<<<<<<<<<<<<<<<<<<<<
cp: can't stat '/mnt/mmc/BlackVue/System/model_info_different.wav': No such file or directory
NAND filesystem : /mnt/mmc/BlackVue/System/model_info_different.wav
Kernel not have yaffs2 filesystems upgrade plz...
sue OK /mnt/mmc/BlackVue/System/upgrade/patch_DR500GW.bin:/mnt/mmc/BlackVue/System/upgrade/patch_DR500GW.sue
▒▒ġ▒▒▒▒ ▒▒▒▒̵▒ ▒▒▒▒ but!! kernel/rootfs upgrade plz..[/mnt/mmc/BlackVue/System/upgrade/patch_DR500GW.bin]
sue OK /mnt/mmc/BlackVue/System/upgrade/uImage_DR500GW:/mnt/mmc/BlackVue/System/upgrade/uImage_DR500GW.sue
Ŀ▒▒ ▒▒▒▒̵▒ ▒▒▒▒..ok [/mnt/mmc/BlackVue/System/upgrade/uImage_DR500GW]
sue OK /mnt/mmc/BlackVue/System/upgrade/cramfsImage_DR500GW:/mnt/mmc/BlackVue/System/upgrade/cramfsImage_DR500GW.sue
▒▒Ʈ▒▒▒Ͻý▒▒▒ ▒▒▒▒̵▒ ▒▒▒▒..ok [/mnt/mmc/BlackVue/System/upgrade/cramfsImage_DR500GW]
[main:1523]img_ok:6, patch_ok:0
[get_version_info:781]app_version:[2.002]
[get_version_info:785]app_model:[500GW]
[get_version_info:789]app_language:[English]
[get_version_info:796]cli_version:[2.220]
[get_version_info:800]cli_model:[500GW]
[get_version_info:804]cli_language:[English]
[get_version_info:811]cfg_version:[1.040]
[get_version_info:815]cfg_model:[500GW]
[get_version_info:819]/mnt/mmc/BlackVue/Config/version.bin read End
INIT: Entering runlevel: 3
Starting telnet daemon.
Starting INET services: done.
Starting syslogd/klogd: done
MontaVista(R) Linux(R) Professional Edition 5.0.0 (0702774)
localhost login: